Just got it.

Attached Images

	IMG_1481[1].jpg (303.7 KB, 34 views)
	IMG_1480[1].jpg (300.0 KB, 23 views)
	IMG_1477[1].jpg (295.7 KB, 30 views)
	IMG_1479[1].jpg (289.8 KB, 26 views)

I have seen HiLOS of this vintage. You should be okay if you are handy. A little TLC goes a long way.

I have a1976 2176B like yours, but a year older. A few years ago, I replaced the Bathroom Upper Wall & Ceiling Panels with shower type paneling. Now, the ceiling mostly at the joints & around the Roof Vent need replacement, which requires removing the Upper Cabinets. The Upper Cabinets near the Door Side need Rebuilt anyhow.

Besides putting a new Coil in the Refrigerator (which I had replaced the whole unit several years ago, removed last year & used a small Walmart refrigerator), last year (problems actually starting a few years ago) the Hydraulic Lift pump wouldn't work at all (I've learned that it's probably just the Brushes, because it's NOT the solenoid). So I had to take it on its annual 200 mile journey while in the raised position and back home. Not doing that again. Because I've now had West Nile Neuroinvasive Disease for a year & a half now, I'm not back in good enough shape to complete that type of work again yet.

So, in May, I upgraded from a 41 year old Hi-Lo to only a 17 year old 2600TFB. Just doing maintenance sealing on the exterior, and nothing else needs any work yet. It's going to be nice for a while NOT to have to do so much annual work on it. All I have to do is complete the sealing work which should be done now, and remove the Awning (which I won't use anyhow, and has been damaged on the lower rear portion due to dragging on the road or something). I thread an 18' x 24' Custom Truck Tarp in, with 8' poles for support, and spread commercial carpeting for a nice Pickin' Parlor and Living Room Sitting area. It makes it nice for a 2 week "annual Festival reunion".

__________________
Formerly 2176B Classic since 1988, needs work!
Now 2600TFB since May 2017
1982 G20 3/4 Ton Chevy Sportvan
Navy Vietnam Vet

Awning parts are hard to come by and probably expensive new. Try and sell your awning and parts. Even if the top is ragged out they can be cut and sewed. Best of luck with your new HiLo.

Awnings solid hooked up kinda weird. If anybody has pics of lower mountings it could be useful.

These are the lower brackets needed for the awning.

Web Store

__________________
"Ruben"
2404T, 2003 2500HD 4X4 GMC Sierra SLT Crew Cab w/Astro camper shell and 2003 Chevy Tahoe LE 4X2
Far West Texas

Those would hang to low for arms. Took pics of whats rigged up doesn't look close to right.Saw lots of pics with those hangers. They hang down instead of up. May just have to do a better job with what I have. First is lower bracket

Attached Images

	IMG_1496[1].jpg (203.1 KB, 7 views)
	IMG_1497[1].jpg (221.3 KB, 8 views)

The top mount shown in your bottom photo appears to be upside down.

__________________
My Great Wife Joyce
2018 Jayco Jay Flight 21QB
Formerly owned 1705T and 2310H
2012 F150 4X4 SuperCrew EcoBoost w/Leer Cap
Reese WD Strait-Line Hitch
Amateur Radio K3EXU

Bottom is hooked under what the canvas attaches to. The 2 bolts are wedging it tight. Is it suppose to just bolt to wood or metal behind it? Bottom one is bolted and wedged with a bolt angled thru the siding. Not done accidentally it goes thru the siding about 2 inches. It can't be close to right.

Ed,

That lower one looks like the Top Bracket going over the roof! And, IF the Awning Connects to it when rolled Up, It's Mounted Correctly, although mine is mounted in the"C" section just below where the Awning is supposed to be Threaded. However, I don't see the Awning anywhere close to it. Although as Rich says, it May be upside down.

The Lower Brackets on mine (All to be removed), your 1st pic, are attached to the bottom of the Upper Section, and hang down about 8". That's why the back one on mine is bent, because it either drug on the Pavement or road at a dip or something.

__________________
Formerly 2176B Classic since 1988, needs work!
Now 2600TFB since May 2017
1982 G20 3/4 Ton Chevy Sportvan
Navy Vietnam Vet

It bolts to the wood/metal and the part that is sticking up above the roof is supposed to be resting against the side wall with a rubber strip spacer in between the two.

__________________
My Great Wife Joyce
2018 Jayco Jay Flight 21QB
Formerly owned 1705T and 2310H
2012 F150 4X4 SuperCrew EcoBoost w/Leer Cap
Reese WD Strait-Line Hitch
Amateur Radio K3EXU

Ok thanks resealing the roof so they are coming off this weekend.

So how are your lower mounts attached

Bolted UP through the Lower Rail.

For Clarity, Remember that this is on my newly acquired 2000 Hi-Lo, which is coming off. Never had one on my 1976.

P.S. Took some Pics of mine this morning to show you, but with my main PC being non-internet capable for several months now, I have no way to connect my camera to my Laptop. Good Pics too!

__________________
Formerly 2176B Classic since 1988, needs work!
Now 2600TFB since May 2017
1982 G20 3/4 Ton Chevy Sportvan
Navy Vietnam Vet

Got my holes in the roof repaired. New fresh air vent in bathroom plumbing vents removed and some weird vent over tub gone also. new Butyl tape under corner trim and fresh air vent. Used Self leveling lap sealant for aluminum patches. Its hot out, so I'm done on the roof today. Still need to remove radio antenna, move TV antenna and apply new Butyl on side trim and front corners before sealing roof.

Attached Images

	IMG_1498[1].jpg (400.2 KB, 10 views)
	IMG_1499[1].jpg (428.9 KB, 9 views)
	IMG_1500[1].jpg (391.0 KB, 10 views)
	IMG_1501[1].jpg (245.6 KB, 9 views)
	IMG_1502[1].jpg (327.8 KB, 10 views)
	IMG_1503[1].jpg (284.2 KB, 9 views)
	IMG_1504[1].jpg (296.4 KB, 13 views)

Here are a couple photos of the upper and lower mounts on a very dirty Hi-Lo. We have been boondocking in a very wet woods

Attached Images

	IMG_20170707_152436062_HDR.jpg (69.8 KB, 12 views)
	IMG_20170707_152321729.jpg (93.3 KB, 8 views)

Thanks my arms are to short for the lower bracket. But I can move the upper one and make it more secure along with lower, rubber spacing will be added. Interiors walls are tore apart so sky's the limit.

This information may be helpful for you. By Sam Shields 7-31-2010 We have done as Sam sugested and it works well.

Thanks good info there

Full Disclosure, I'm mostly a rookie to all this. That said, I did just completely rebuild the entire roof on ours. Anyway, the lap sealant is good and all, but I'd also be running Eterna Bond tape over all the seams/screws on those patches. The stuff is amazing. Easy to work with, and really makes a strong seal:

https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1

I like the stuff so much, I actually ran it all along the outside edge of my roof to make a more seamless seal on the roof molding.

You can see the Eterna Bond on our HiLo here:
https://photos-3.dropbox.com/t/2/AAC...00&size_mode=3

The stuff works so well, I used it on the roof of our house after it was destroyed by a hail storm about 2 months ago. Have a roofer lined up to replace it, but I needed to patch up numerous holes to get us by in the mean time. We had holes large enough that I could stick my finger through the shingles AND the plywood under it. Baseball sized hail is nasty! At any rate, the EternaBond patched everything up and we haven't had a single leak during subsequent storms. The stuff just works.

(also, it's super annoying that I can upload photos when replying from my phone, but i can't when replying from my computer).

__________________
-Nick Malozzi
72 HiLo Traveler aka 'The Dolly Roger'