|
11-02-2020, 11:35 AM
|
#1
|
Member
Join Date: Nov 2020
Location: Texas
Posts: 4
|
No lights, radio, fan in camper.
I don't know what the year, model and serial number is for my camper. Recently, the camper was moved from a camp site to a permanent spot. After setting the camper up only two of the AC outlets worked. the one in the very front of the camper and the one under the left side couch. While troubleshooting the issue the two GFCI in the side of the cabinets on both sides of the camper had proper (124 volts) coming into them, however, voltage dropped to 96 volts within the GFCI outlets. After replacing the outlets it fixed all the other outlets in the camper.
However, none of the fans and lights in the camper are working. The fuse box is under the bathroom sink. Any information that you are able to provide me is greatly appreciated.
Thank you,
Dustin Baker
__________________
|
|
|
11-02-2020, 12:32 PM
|
#2
|
Moderator
Join Date: Feb 2010
Location: NW PA
Posts: 3,386
|
If you have have the wire bundle in the back corner that flexes with the trailer going up and down check to see if there are any loose connections there. I've seen others that have had problems there.
__________________
__________________
My Great Wife Joyce
2018 Jayco Jay Flight 21QB
Formerly owned 1705T and 2310H
2012 F150 4X4 SuperCrew EcoBoost w/Leer Cap
Reese WD Strait-Line Hitch
Amateur Radio K3EXU
|
|
|
11-02-2020, 02:40 PM
|
#3
|
Senior Member
Join Date: Oct 2011
Location: Berwick. Pa
Posts: 347
|
After you put the camper up did you move the 3 position master switch to the right position?
__________________
Cheers
Garyk52
DW Judy
96 24' Hi-Lo Funchaser, (99 Aliner Sofabed Sold 6/9/18)
06 Toyota Tundra SR5 Access Cab 4X4 36,000 miles and counting
|
|
|
11-02-2020, 02:44 PM
|
#4
|
Member
Join Date: Nov 2020
Location: Texas
Posts: 4
|
garyk52,
I am not sure? I believe it is in the neutral position. Do you know what position it should be in.
Thanks
|
|
|
11-02-2020, 02:52 PM
|
#5
|
Member
Join Date: Nov 2020
Location: Texas
Posts: 4
|
RichR,
I located the wire bundles, followed them into the cabinet under the sink. I don't see any loose connections. The solar panel input has the correct voltage (during the day), but at the fuse panel I have no voltage. I also measured the voltage coming out of the PC-30 (Power Source/Battery Charger) which is around 13.2. After the Converter/Load panel the voltage is consistently 12.8 volts. However, the fuse panel has no voltage.
Thanks
|
|
|
11-02-2020, 04:23 PM
|
#6
|
Site Team
Join Date: Jul 2010
Location: Pine, AZ
Posts: 4,692
|
Dustin, the 3-position Master Switch should be in the position opposite the top lifting position. The middle position is the "neutral" position and if it's there, nothing works except for the refrigerator. The switch should be rocked to an outside position, where the top lifting switch does not work.
- Jack
__________________
Hi-Lo 1707T - Tire Minder TPMS on Tow Vehicle and Trailer, 300W Solar Battery Charger, Equal-i-zer WDH, Progressive Dynamics Converter, Fan-Tastic Fan, LiFePO4 battery 12V DC Electrical System, SoftStartRV mounted on A/C
2024 F150 Platinum FX4 3.5L PowerBoost SCrew
|
|
|
11-02-2020, 04:28 PM
|
#7
|
Member
Join Date: Nov 2020
Location: Texas
Posts: 4
|
I will try this tonight to see if it whats causing my issue...
Do you happen to know what model has the fuse panel in the restroom?
Thank you,
|
|
|
11-02-2020, 04:50 PM
|
#8
|
Site Team
Join Date: Jul 2010
Location: Pine, AZ
Posts: 4,692
|
I don't know anything about the location of fuse boxes other than they would always be in the lower half, probably at floor level.
Your symptoms sound like the Master Switch is in the wrong position, not a fuse problem.
- Jack
|
|
|
11-12-2020, 05:37 PM
|
#9
|
Member
Join Date: Jul 2011
Location: southern california
Posts: 59
|
On my 2305 there are wire nuts in the wire bundle under the cloth covering. I had a similar issue and found the ground was loose in the wire but. I took it apart and reinstalled the wire but and everything worked.
On my trailer the three position switch does not affect the lights or fans but it would make sense for it to.
The fans and lights in the top half should all be 12 volt to the beat of my knowledge
__________________
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|