frame

Hi! I have a 2018 Freelander 27QB. I was underneath the rig on the driver's side. Behind the B-Pillar, but in front of the Generator is another 12V battery sitting in a battery holder mounted to the frame. The battery is grounded to the frame, but the positive cable is routed up into the...

So I noticed that the Frame on the door side of my chalet is bent most likely from using the step to get inside. Looking for ideas on how to bend it back into place and secure it otherwise I cannot use the steps.

Been searching for an hour on the forums before posting this. The rear side fixed windows in Coachmen’s Ruby Brookstone hold water after a rain. Do I remove the window to cure or what? Thanks in advance for direction. Bill

I just finished applying the full POR15 treatment plus topcoat to my 22-year old dual axle steel boat trailer, which has been stowed outdoors in Florida for the past 16 years. I had to have the three main steel cross pieces that support the boat bunks replaced with new steel due to excessive...

I made a underfloor spare tire bracket for our toyhauler and mounted it this weekend. Basically a 2x2 tube steel and end plates, with a threaded rod and oversized wing nut and large steel plate for the washer. It was a small chore to get the tire up there, but hopefully I won't have to ever...

I haven't even camped in our A122 yet as we just got it. I have tightened loose screws, added usb ports and a voltage meter. I got a Curt BetterWeigh mobile tow scale and playing with it. So far it's very accurate as to tounge weight, trailer weight and total GCWR. Alas, waxed the body as well...

Hi. I'm prepping my Propride P3 for installation and need to measure the height of the trailer frame so I can determine how to configure the hitch bar. Unfortunately, my trailer is 10 miles away. Can someone measure the same on their late-model Mini/Micro-lite, if convenient? Thanks From...

I know there's another recent solar thread, but this is more specific. Can anyone post photos of your method/hardware to mount solar panels on the front roof of your A-frame? I am going to do one or possibly two (if they'll fit) 100W panels this year. I have seen Slim Potatohead's install on...

Hi fellow AFrame owners ~ We own a A122 and do not have any sort of canopy. Might you have a recommendation as to how we can hang a metal wind spinner without damaging the side of the AFrame? Thank you very much!: :anim_snoopy:

Hi guys, I have a solid 12V system going, but want to get at least a poor-man's simplistic 110V system via an inverter. Currently I have 2 AGM batteries wired in parallel, with 200AH. I'm running 200 watts of solar via an integrated Renogy suitcase with charge controller. I'm thinking I'm...

Hi Does anyone know what will remove the white dealer marker, from my frame? I tried scrubbing with a pad but it started to take the frame paint off. There's a dealer number and model number on the front of my frame. Any one got any suggestions please?

We traded in our 2016 FR a frame after we had it for a couple of years. Not the only reason, but we were quite disgruntled with Forest Rivers reaction to the issues with burning up the roof actuators (we were on our fourth in a year). Our purchased extended warranty was about to run out when...

I noticed this today. We've been parked for two weeks and that compartment holds the fresh water stuff so it's rarely opened. It's the fourth one from the front on the driver's side and the hinge side is under the kitchen slide. As far as I recall that door has been locked since we arrived. The...

Have a 2012 34rlsa we are the second owner. On the drivers side I am having flexing and stress cracks where the wall turns down toward the jack Cedar Creek has denied fixing it. To me a frame is a serious problem and shouldn't crack in less than ten thousand miles.

Just wanted to post this as information to others. There is lots of information out there saying NO to weight distribution hitches on c-channel tent/pop up trailer frames. Well, I did it and here is my experience, which has been proven over 7000+ KMs of towing. The trailer is a Palomino...

I am going to add the morryde suspension to my 5 th over the winter.Where is the best places to support the frame ? I was planning to support it ,behind each back tire and just ahead of the front tire,right under the frame on both sides. Will it be enough support with the front land gear down?

I have been reading this forum to learn more about the a-frames... My wife and I are looking to purchase an A-frame this Spring, either new or not older than 3 or 4 years. I want it to be able to sleep 3 adults, most of the time it will be just the two adults. Tow vehicle is F150. The trailer...

Hi. I am new to the thread, and joined mainly to investigate possible solutions to my leaky living room window (frame, NOT glass) in the large slide-out on our 2016 berkshire XLT 43-A. I have checked the exterior glass-to-wall interface seal, and even applied some silicone sealant... still...

Does anyone know what type of wood is used on the Isata 5 Cabinet Face Frames? It looks like maple but I want to be sure. Thanks.

Does anyone know the material that the bubble windows are made from. Also, does anyone know of a good way to clean the outside window surface?

Got a new project delivered. Not sure what year though? Got it delivered on Saturday and stripped down Sunday! Had a sink and stove, but did not see a furnace. I am thinking to do the following and appreciate any advice for this build: Make it a shell that rest on the truck's bed rails Chop...

Ouch. We have an A102 which we love very much. So a month ago I did pull the drains and also drained the freshwater tank. then I had some travel for a month in Washington. By the time I returned, the temps here in Montana had dropped to near 0f and have been there a while. This morning I went...

Wondering if anyone has had this problem, the lifting arm started making noise, and running slow. I noticed a rubber seal extruded from the body of the lifting arm. It still worked, but noisy. I took the arm off and tried to call the manufacturer/company listed on the motor of the arm. Rieco...

We recently purchased a rockwood a122 aframe and we are in love with it. Question does it need a cover to withstand a northeast Indiana winter with average of 13 inches of snowfall? If so any suggestions of brand, etc?

My shower door handle came loose, possibly missing set screw. Appears to be attached with a black rubber sheet to protect glass and some type adhesive, there is a hole on glass and aluminum handle where I think there was a set screw.